Store

RTI Mora Standard 125cc plenum and valve adjustment controls

RTI Mora Standard regulator gauge Foster fill port and pistol grip

RTI Mora Standard rear stock adjustable cheekpiece and action

Close-up of the RTI Mora Standard pressure gauge, 125cc plenum housing and internal action components.

RTI Mora Standard V2 Gen 2 PCP Air Rifle – 700cc, 60cm

The RTI Mora Standard V2 Gen 2 is the middle Mora—and the best all-around configuration for many shooters. Its 600mm / 24-inch barrel and 700cc carbon-fiber bottle provide more barrel length and air capacity than the Compact without stepping up to the longer, heavier Sniper.

Available from Edgun West in .22, .25, and .30 calibers, the Mora Standard is built for precision pellets, modern airgun slugs, and shooters who want direct control over regulator pressure, valve dwell, and projectile setup.

RTI Mora Standard at a Glance

600mm / 24-inch barrel

700cc carbon-fiber bottle
885mm / 34.8-inch overall length
Approximately 9.7 pounds before optic and accessories
125cc regulated power plenun
Twin-regulator system with externally adjustable second stage
Externally adjustable pressure-assisted valve
Maximum 300-bar / 4,350 PSI fill pressure
Adjustable 20–150 MOA Picatinny optics rail
Adjustable two-stage trigger
Side-lever action and reversible magazine

Choose Your Caliber

Caliber	Barrel	Magazine	Published Range	Best Fit
.22	RTI RPB, 1:16, light choke	19 rounds	60–122 J / 44–90 ft-lb Up to 45 shots	Efficiency, capacity, pellets and lighter slugs
.25	RTI RPB, 1:20, light choke	15 rounds	80–175 J / 59–129 ft-lb Up to 35 shots	Best balance of power, efficiency and versatility
.30	Lothar Walther, 1:16, choked	13 rounds	110–200 J / 81–148 ft-lb Up to 30 shots	Heavy projectiles and maximum downrange energy

Energy and shot-count figures are RTI’s published performance ranges for the 700cc Standard. Actual results depend on regulator pressure, valve dwell, ammunition, velocity, and fill-pressure range.

What Is Included

RTI Mora Standard V2 Gen 2 rifle
Customer-selected .22, .25 or .30 caliber
700cc carbon-fiber bottle
Two magazines in the selected caliber
RTI Hušh 50 carbon moderator
M-LOK bottle shield
Heavy-duty fitted hard case

Why buy from Edgun West? The Mora is an advanced tuning platform not a generic PCP that should be sold with one copied paragraph. Edgun West provides U.S.-based help with model selection, caliber choice, ammunition compatibility, and understanding the rifle’s tuning system before and after the sale.

Caliber

Price:

$2,449.00

Add to Cart

RTI Mora Engineering and Tuning Guide

System	How It Works	Why It Matters
Twin Regulation	Two regulator stages control pressure before air enters the 125cc plenum. The second stage is externally adjustable.	Allows pressure to be matched to caliber, projectile weight and desired velocity.
Assisted Valve	Uses pressure from the barrel to help close the valve rapidly. Valve dwell is externally adjustable.	Controls how much regulated air is released per shot and helps balance output, consistency and efficiency.
Valve Dwell	Longer dwell releases more air. Shorter dwell reduces air use.	The goal is consistent velocity with the chosen ammunition—not simply maximum speed.
Projectile Headspace	The probe position can be adjusted to change projectile seating depth.	Lets the shooter test deeper pellet seating or shallower slug seating for improved performance.
Barrel Support	The barrel can be free-floating or supported beneath the scope area.	Allows the owner to choose maximum barrel isolation or added support for transport and field use.
Projectile Length	The magazine accepts projectiles up to about 22mm. Projectiles up to about 25mm can be single-loaded.	Provides compatibility with a broader range of longer airgun slugs.
Adjustable Optics Rail	The 18-slot Picatinny rail adjusts from approximately 20 to 150 MOA.	Preserves more scope adjustment for heavy-projectile trajectories and extended-distance shooting.
Trigger	First stage, second stage, sear engagement, blade height and blade angle can be adjusted.	Allows the trigger position and break to be fitted to the shooter while retaining safe engagement.
Reversible Magazine	The magazine can be configured for loading from either side.	Supports both right- and left-handed setups.
Witness Holes	External holes correspond with specific internal O-rings.	Helps isolate the location of a leak without blindly dismantling the rifle.
Removable Valve Assembly	The valve can be removed without completely stripping unrelated sections of the action.	Simplifies diagnosis, seal replacement and long-term service.
Caliber Conversion	Supported with the correct barrel, probe, magazine and caliber-specific components.	One Mora can support multiple calibers, but each conversion requires a new pressure, dwell and ammunition setup.

Recommended tuning order: select the projectile, set regulated pressure, adjust valve dwell, allow the regulator to stabilize, chronograph several shots and confirm accuracy before finalizing the tune.

RTI Mora Standard Complete Specifications

Specification	RTI Mora Standard V2 Gen 2
Available Calibers	.22 / 5.5mm, .25 / 6.35mm and .30 / 7.62mm
Action	Precharged pneumatic, side lever
Barrel Length	600mm / 24 inches
Overall Length	885mm / 34.8 inches
Approximate Bare Weight	4,400g / 9.7 lb
Height	195mm from grip bottom to optics rail
Action Width	40mm
Air Bottle	700cc carbon fiber
Bottle Diameter	60mm / 2.36 inches
Maximum Fill Pressure	300 bar / 4,350 PSI
Fill Connection	Standard Foster quick-connect
Plenum	125cc
Regulator System	Twin regulation; externally adjustable second stage, approximately 50–200 bar
Valve	Externally adjustable pressure-assisted valve
Trigger	Adjustable two stage; down to approximately 200g
Safety	180-degree manual safety; mechanically locks hammer
Optics Rail	190mm, 18-slot Picatinny; approximately 20–150 MOA adjustment
Pressure Gauges	Bottle pressure and regulated/plenum pressure
Magazine Projectile Length	Up to approximately 22mm
Single-Loaded Projectile Length	Up to approximately 25mm
Magazine Orientation	Reversible for right- or left-side loading
Grip	Standard AR-15 pattern
Accessory Mounting	M-LOK-compatible mounting locations
Caliber Conversion	Supported with the correct RTI barrel, probe, magazine and related parts

RTI Mora Standard FAQ

What is the difference between the Mora Compact, Standard, and Sniper?
The Compact uses a 500mm barrel and a 500 cc bottle. The Standard uses a 600mm barrel and a 700 cc bottle. The traditional Sniper uses a 700mm barrel and 1100cc bottle. The Standard is the middle configuration in barrel length, overall length, weight and air capacity.

Which caliber should I choose?
Choose .22 for magazine capacity, air efficiency and broad ammunition selection. Choose .25 for the strongest overall balance of power and efficiency. Choose .30 for heavier projectiles and maximum downrange energy.

Will all three calibers shoot pellets and slugs?
Yes, but every barrel will prefer specific projectile diameters, weights and velocities. The .22 and .25 use RTI RPB barrels. The .30 Standard uses a choked Lothar Walther barrel.

How many shots will it produce?
RTI publishes up to approximately 45 shots in .22, 35 in .25 and 30 in .30 for the 700cc Standard. Actual shot count depends on pressure, valve dwell, projectile, velocity and the usable fill range.

How powerful is the Mora Standard?
RTI publishes 60–122 joules for .22, 80–175 joules for .25 and 110–200 joules for .30. These figures represent the platform’s tuning range and are not guaranteed out-of-box settings.

Does it have to be filled to 300 bar?
No. 300 bar is the maximum published pressure, not the required fill pressure for every session. Use only dry compressed air and properly rated filling equipment.

When should it be refilled?
RTI instructs the owner to refill when reservoir pressure approaches the regulated-pressure reading.

Does it include a scope?
No. Scope and rings are selected separately to match the intended range, projectile and shooting application.

Does it include a moderator?
Yes. The standard package includes the RTI Hušh 50 carbon moderator where lawful.

Can the magazine load from either side?
Yes. The magazine can be reversed for right- or left-side loading.

Can the Mora Standard change calibers?
Yes. A conversion requires the correct barrel, probe, magazine and related RTI components. The rifle must then be retuned for the new caliber and projectile.

Why buy from Edgun West?
Edgun West provides U.S.-based assistance with Mora model selection, caliber choice, ammunition compatibility and understanding the platform’s tuning and service systems. The objective is not simply to sell the rifle—it is to help the customer select the correct Mora and understand what they are buying.