Store

RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm
RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm

RTI Mora Sniper V2 Gen 2 .35 / 9mm PCP Air Rifle – 700cc, 70cm



The RTI Mora Sniper V2 Gen 2 .35 / 9mm is the heavyweight Mora. It is built around a 700mm / 28-inch Lothar Walther barrel, 125cc plenum and RTI’s externally adjustable regulated valve system. The Edgun West version uses a slimmer 700cc carbon-fiber bottle rather than the traditional 1100cc Sniper bottle.


This is a dedicated big-bore PCP air rifle for shooters who want heavier projectiles and substantially greater energy than the .22, .25 or .30 Mora configurations. It is not a firearm and does not use 9mm Luger ammunition.


RTI Mora .35 / 9mm at a Glance

Caliber.35 / 9mm airgun caliber
Barrel700mm / 28-inch Lothar Walther, 1:16 twist, unchoked
Air Bottle700cc carbon fiber
Plenum125cc
Magazine Capacity9 rounds
RegulationTwin regulator system with externally adjustable second stage
ValveExternally adjustable pressure-assisted valve
Maximum Fill Pressure300 bar / approximately 4,350 PSI
Overall Length985mm / 38.8 inches

Manufacturer-Published Performance

Published Energy Range130–305 joules / approximately 96–225 ft-lb
Published Regulated Pressure Range100–200 bar / approximately 1,450–2,900 PSI
Published Shot CountRTI lists up to approximately 30 shots for its 1100cc reference Sniper

The energy and shot-count figures above come from RTI’s published 70cm .35 Sniper data. RTI’s published shot-count test uses an 1100cc bottle. This Edgun West rifle uses a 700cc bottle, so exact energy, velocity and shot count will depend on its production setup, regulator pressure, valve dwell and selected projectile.


What Is Included

  • RTI Mora Sniper V2 Gen 2 .35 / 9mm
  • 700mm / 28-inch barrel
  • 700cc carbon-fiber bottle
  • Two 9-round magazines
  • RTI carbon moderator
  • M-LOK bottle rail
  • Heavy-duty fitted hard case


Why buy it from Edgun West? This is not a generic dropdown caliber. Projectile diameter, weight, length, regulator pressure, valve dwell and headspace all matter. Edgun West provides U.S.-based help selecting ammunition, understanding the rifle’s tuning system and setting realistic expectations for the exact 700cc configuration being sold.



Price:
$2,549.00
RTI Mora Sniper .35 / 9mm Complete Specifications

SpecificationRTI Mora Sniper V2 Gen 2 .35 / 9mm
Edgun West Configuration700cc carbon-fiber bottle with 700mm barrel
Caliber.35 / 9mm airgun caliber
ActionPrecharged pneumatic, side lever
BarrelLothar Walther
Barrel Length700mm / 28 inches
Twist Rate1:16 inches
ChokeUnchoked
Overall Length985mm / 38.8 inches
Height195mm from bottom of grip to optics rail
Action Width40mm
Exact 700cc Configuration WeightTo be verified when the incoming production rifles are received
Air Bottle700cc carbon fiber
Maximum Fill Pressure300 bar / approximately 4,350 PSI
Charging ConnectionStandard Foster quick-connect
Plenum Volume125cc
Regulator SystemTwin regulation
Second RegulatorExternally adjustable from approximately 50–200 bar
Published Performance Pressure Range100–200 bar / approximately 1,450–2,900 PSI
ValveExternally adjustable pressure-assisted valve
Hammer SystemAutomatic air-spring system matched to regulated pressure
Manufacturer-Published Energy130–305 joules / approximately 96–225 ft-lb for the 70cm .35 Sniper platform
Manufacturer-Published Shot CountUp to approximately 30 shots with RTI’s 1100cc reference bottle; no official 700cc figure published
Magazine Capacity9 rounds
Maximum Magazine Projectile LengthApproximately 22mm
Maximum Single-Loaded Projectile LengthApproximately 25mm
Magazine OrientationReversible for right- or left-side loading
TriggerFully adjustable two stage; adjustable down to approximately 200 grams
Trigger AdjustmentsSear engagement, first-stage travel, first-stage weight, second-stage weight, blade height and blade rotation
Safety180-degree manual safety that mechanically locks the hammer system
Optics Rail190mm, 18-slot Picatinny rail
Rail Elevation AdjustmentApproximately 20–150 MOA
Pressure GaugesBottle pressure and regulated/plenum pressure
GripStandard AR-15 pattern
Accessory MountingM-LOK-compatible mounting locations and included bottle rail
Barrel SupportCan be configured as free-floating or supported beneath the optics area
Sound ManagementIntegral monocore system where lawful, plus included carbon moderator
Leak DiagnosisExternal witness holes correspond with individual internal O-rings
Caliber ConversionSupported with the correct RTI barrel, probe, magazine, seals and related components
WarrantyThree-year RTI manufacturer warranty handled through the selling dealer
Included EquipmentTwo magazines, carbon moderator, M-LOK bottle rail and heavy-duty fitted hard case


RTI Mora .35 / 9mm Engineering and Tuning Guide

SystemHow It WorksWhy It Matters in .35 / 9mm
Twin RegulationTwo regulator stages reduce bottle pressure before air enters the 125cc plenum.Provides the controlled working pressure needed for heavy .35-caliber pellets and slugs.
First RegulatorNormally set near 200 bar and generally left unchanged.The first stage should remain above the selected second-stage pressure. It is not the routine tuning control.
Second RegulatorExternally adjustable and controls the pressure supplied to the plenum.Higher pressure may support heavier projectiles or greater velocity but also increases air consumption.
125cc PlenumStores regulated air immediately before each shot.Provides the regulated air volume required for the Mora’s published big-bore performance range.
Air-Spring HammerAutomatically responds to plenum pressure without a conventional external hammer-spring tune.Reduces the number of independent adjustments required when changing regulated pressure.
Valve DwellControls how long the valve remains open and how much regulated air reaches the barrel.Heavy .35 projectiles may require more air, but excessive dwell wastes air without necessarily improving accuracy.
Projectile HeadspaceThe projectile probe can be adjusted to change seating depth.Different .35 pellets and slugs may require different seating positions relative to the transfer port and rifling.
Unchoked BarrelThe 700mm Lothar Walther barrel uses a 1:16 twist and no muzzle choke.Projectile diameter and fit become especially important. Do not assume every product labeled .35 or .357 will perform the same.
Projectile LengthMagazine length is approximately 22mm; single-loaded projectiles may be approximately 25mm.Long, heavy slugs may exceed magazine length even when their diameter is correct.
700mm BarrelProvides additional time for expanding air to accelerate the projectile.Can produce the desired velocity more efficiently than a shorter barrel when the pressure and dwell are properly balanced.
700cc BottleStores the same maximum pressure as the published Mora system but less total air than the 1100cc reference bottle.Expect fewer shots per fill than RTI’s 1100cc reference configuration at the same power setting.
Adjustable Optics RailProvides approximately 20–150 MOA of coarse elevation adjustment.Helps preserve the scope’s internal elevation range for heavy-projectile trajectories.
Witness HolesCorrespond with individual internal O-rings.Helps isolate a leak before unnecessary disassembly of the high-pressure system.

Recommended Tuning Sequence


  • Select one known projectile diameter, weight and design.
  • Confirm that the projectile fits the magazine or plan to single-load it.
  • Record the rifle’s original regulator and valve settings.
  • Set the second regulator for the intended performance level.
  • Fire several shots to allow the regulator to stabilize.
  • Begin with the valve dwell open and reduce it gradually.
  • Chronograph several shots after every adjustment.
  • Find the dwell setting that produces the smallest velocity variation.
  • Adjust projectile headspace only after pressure and dwell are stable.
  • Confirm accuracy at the actual intended distance.
  • Record the completed tune, projectile and fill-pressure range.


Do not tune around one maximum-velocity shot. The useful tune is the one that delivers stable velocity, accuracy and repeatable regulator recovery without wasting the limited air stored in the 700cc bottle.


Important .35 / 9mm Notes


  • “.35,” “.357” and “9mm” are common search terms, but exact projectile diameter still matters.
  • This rifle does not use 9mm Luger ammunition or any firearm cartridge.
  • Projectile length may prevent some heavy slugs from fitting the magazine.
  • Change only one tuning variable at a time.
  • Use a chronograph whenever pressure, dwell, projectile or seating depth is changed.
  • Only use dry compressed air and properly rated filling equipment.



RTI Mora Sniper .35 / 9mm Frequently Asked Questions

Is the RTI Mora .35 the same as a 9mm firearm?
No. The 9mm designation refers to the approximate airgun projectile diameter. The rifle does not accept 9mm Luger ammunition, firearm cartridges, primers or gunpowder.


Is .35 the same as .357?
The terms are often used interchangeably in airgun searches, but projectile diameter can vary. Use ammunition specifically verified for the rifle’s barrel. Do not assume every slug marked .35, .356 or .357 will fit or shoot accurately.


What barrel does the .35 Mora use?
RTI lists the 700mm / 28-inch .35 Sniper barrel as a Lothar Walther barrel with a 1:16-inch twist and no choke.


How powerful is the RTI Mora .35?
RTI publishes a performance range of 130–305 joules, approximately 96–225 ft-lb, for the 70cm .35 Sniper platform. Exact output depends on projectile, regulated pressure, valve dwell and production setup.


Does the Edgun West 700cc rifle produce 305 joules?
The core 70cm barrel, 125cc plenum and regulated valve system support the same type of high-output tune, but RTI’s published test data is tied to its 1100cc reference Sniper. Edgun West will not guarantee 305 joules for the exact 700cc version until the incoming rifles are tested.


How many shots will the 700cc version produce?
RTI publishes up to approximately 30 shots for its 1100cc reference configuration. The 700cc bottle stores less total air, so its shot count will be lower at an equivalent tune. Actual results depend heavily on projectile weight, pressure, dwell and the chosen usable fill range.


Why choose the 700cc bottle?
The 700cc bottle produces a slimmer, less bulky rifle than the traditional 1100cc Sniper. The tradeoff is fewer shots per fill at the same power setting.


What is the magazine capacity?
The .35 / 9mm magazine holds nine rounds.


What is the maximum projectile length?
The magazine accepts projectiles up to approximately 22mm long. Projectiles up to approximately 25mm may be loaded individually without the magazine.


Will every .35 pellet or slug fit the magazine?
No. Diameter, nose shape and overall length all matter. Some heavy or high-ballistic-coefficient slugs may require single loading.


What projectile weight should I use?
There is no single universal weight. The correct projectile must fit the barrel and magazine and produce stable accuracy at the selected velocity. Edgun West recommends testing a controlled selection rather than purchasing large quantities before confirming compatibility.


Does the rifle require a 300-bar fill?
No. Three hundred bar is the maximum published fill pressure, not a required pressure for every shooting session.


When should the rifle be refilled?
RTI instructs the owner to refill when bottle pressure approaches the regulated-pressure reading.


What do the two gauges display?
One gauge displays bottle pressure. The other displays regulated or plenum pressure.


Can the magazine be loaded from either side?
Yes. The reversible magazine can be configured for right- or left-side loading.


Does the rifle include a scope?
No. Scope and rings are selected separately to match the intended projectile, range and shooting application.


Does it include a moderator?
Yes. The Edgun West package includes a carbon moderator. Use is subject to the laws applicable in the purchaser’s location.


Can the Mora .35 change calibers?
Yes. A conversion requires the proper RTI barrel, projectile probe, magazine, seals and related components. Regulator pressure, valve dwell, headspace and ammunition must then be reset for the new caliber.


Is the barrel choked?
No. RTI identifies the 70cm .35 Lothar Walther barrel as unchoked.


What is projectile headspace?
Headspace describes where the projectile sits relative to the transfer port and the beginning of the rifling. The Mora probe can be adjusted to change seating depth for different projectile designs.


What do the witness holes do?
Each witness hole corresponds with a specific internal O-ring. Soapy water around the holes can help identify the leak's location before the rifle is disassembled.


What warranty does RTI provide?
RTI publishes a three-year manufacturer warranty and instructs customers to contact the selling dealer first.


Why buy the RTI Mora .35 from Edgun West?
Edgun West is selling a specific 700cc U.S. configuration rather than blindly copying data from RTI’s 1100cc European reference rifle. We clearly separate verified specifications, manufacturer reference figures, and results that still require testing. Customers receive U.S.-based guidance on ammunition, setup, filling requirements and the rifle’s tuning system.